Tuesday, May 29, 2012

Puppet ~ a beginners concept guide (Part 1)

Someone asked me where to start with Puppet learning. I pointed them at PuppetLabs online doc for Puppet, which is actually nice for a proper understanding. 
But for someone trying to start with Puppet, that documentation is a bit long to read similar to any book. 
I searched for few blogs, but didn't found any content (short but enough, fundamentals but usable) that I was looking for.
____________________________________________________


Puppet
beginners concept guide (Part 1)

[] What  it  is?  When  is  it  required?  (for all new guys, who came here while just browsing internet)
Puppet is an OpenSource automated configuration management framework (which means a tool that knows how to configure all machines to a deterministic state once you provide it the required set of manifests pulling the correct strings).
It's managed at enterprise level by an organization called PuppetLabs (http://puppetlabs.com/).

It is required#1 when you have a hell-lot of machines required to be configured in a similar form.
It is required#2 when you have a infrastructure requirement of dynamic scale-up and scale-down of machines with a pre-determined (or at least metadata-calculated) configuration.
It is required#3 to have a control over all set of configured machines, so a centralized (master-server or repo-based) change gets propagated to all automatically.
And more scenarios come up as you require it.

_____________________________________


[] Quickie.

Install Ruby, Rubygems on your machine where you aim to test it.
$ gem install puppet --no-ri --no-rdoc
Download installers @Windows  @MacOSX ::&:: Docs to installing.

Checking, if it's installed properly and acting good
Now, 'puppet --version' shall give you the version of installed puppet once succeed.
Executing 'facter' and you shall get a list of System Environment related major information.

Have a quick puppet run, this shall create a directory '/tmp/pup' if absent. Creates a file '/tmp/pup/et' with 'look at me' as its content.
{In case of trying out on platforms without '/tmp' location. Like for Windows, change '/tmp' with 'C:/' or so}

$ puppet apply -e "file{'/tmp/pup':
                               ensure => 'directory'}
                             file{ '/tmp/pup/et':
                               ensure => 'present',
                               content => 'look at me',
                               require => File['/tmp/pup']}
                           "

_____________________________________


[] Dumb  usage  structure.
Create huge manifest for your node with all resources & data mentioned in it. Then directly apply that manifest file instead of '-e "abc{.....xyz}"'.

Say if the example above is your entire huge configuration commandment for the node. Copy all that to a file say 'mynode.pp'.
Then apply it similarly like
$ puppet apply mynode.pp

_____________________________________


[] How  it  evolves?

Now, as any application had pluggable library components to be loaded and shared as and when required. Puppet too have a concept of modules. These modules can have manifests, files-serving and more.

Modules can be created in any design preference. Normally it works by having different modules per system component. To entertain different logical configuration states for any given system component (and also keeping it clean) further re-factoring can be done in the modules' manifest dividing it into different scopes.

Taking example of a module for 'apache httpd'. For a very basic library, you might wanna structure your module like

  • a directory base for your module:  <MODULE_PATH>httpd/
  • a directory in module to serve static files:   <MODULE_PATH>/httpd/files
  • static configuration file for httpd:   <MODULE_PATH>/httpd/files/myhttpd.conf
    AccessFileName .acl
  • directory to hold your manifests in module:   <MODULE_PATH>/httpd/manifests/
  • a complete solution manifest:   <MODULE_PATH>/httpd/manifests/init.pp
    class httpd{
      include httpd::install
      include httpd::config
      include httpd::service
    }
  • a manifest just installing httpd:    <MODULE_PATH>/httpd/manifests/install.pp
    class httpd::install {
      package {'httpd': ensure => 'installed'}
    }
  • a manifest just configuring httpd:    <MODULE_PATH>/httpd/manifests/config.pp
    class httpd::config{
      file {'/etc/httpd/conf.d/httpd.conf':
        ensure => 'present',
        source => 'puppet:///modules/httpd/myhttpd.conf'
      }
    }
  • a manifest just handling httpd service:  <MODULE_PATH>/httpd/manifests/service.pp
    class httpd::service{
      service{'httpd': ensure => 'running' }
    }

Now, using it

  $ puppet apply --modulepath=<MODULE_PATH>  -e "include httpd"
would install, custom-configure and start the httpd service.


  $ puppet apply --modulepath=<MODULE_PATH>  -e "include httpd::install"
would just install the httpd service.



________________________________________________________________

Part2: Road to Modules

2 comments:

  1. I'm working on a book which may help: The Puppet Beginner's Guide. If you have time to take a look, I'd appreciate it!

    http://bitfieldconsulting.com/pbg

    ReplyDelete
    Replies
    1. @JohnArundel outline seems nice, do you plan on covering puppet custom add-on... also it will be good to include habits around tools like librarian-puppet, puppet-lint and rspec-puppet.

      Delete